I have a raspberry pi zero w connected to the Elecrow lorawan gateway hat v1.0 (purple).
I enabled I2C and SPI. I keep getting errors about resetting lr1302 when running the reset script.
I get error about cannot start sx1250 when trying to start packer forwarder.
Any help would be appreciated. The Module is a LR1302.
SX1302_RESET_PIN=24 # SX1302 reset
SX1302_POWER_EN_PIN=2 # SX1302 power enable
SX1261_RESET_PIN=11 # SX1261 reset (LBT / Spectral Scan)
AD5338R_RESET_PIN=22 # AD5338R reset (full-duplex CN490 reference design)
tyro@rpiz:~/LR1302_loraWAN/LR1302_HAL/sx1302_hal/tools $ ./reset_lgw.sh start
CoreCell reset through GPIO24…
SX1261 reset through GPIO24…
CoreCell power enable through GPIO2…
CoreCell ADC reset through GPIO22…
*** Packet Forwarder ***
Version: 2.1.0
*** SX1302 HAL library version info ***
Version: 2.1.0;
INFO: Little endian host
INFO: found configuration file global_conf.json, parsing it
INFO: global_conf.json does contain a JSON object named SX130x_conf, parsing SX1302 parameters
INFO: com_type SPI, com_path /dev/spidev0.0, lorawan_public 1, clksrc 0, full_duplex 0
INFO: antenna_gain 0 dBi
INFO: Configuring legacy timestamp
INFO: Configuring Tx Gain LUT for rf_chain 0 with 16 indexes for sx1250
INFO: radio 0 enabled (type SX1250), center frequency 904300000, RSSI offset -215.399994, tx enabled 1, single input mode 0
INFO: radio 1 enabled (type SX1250), center frequency 905000000, RSSI offset -215.399994, tx enabled 0, single input mode 0
INFO: Lora multi-SF channel 0> radio 0, IF -400000 Hz, 125 kHz bw, SF 5 to 12
INFO: Lora multi-SF channel 1> radio 0, IF -200000 Hz, 125 kHz bw, SF 5 to 12
INFO: Lora multi-SF channel 2> radio 0, IF 0 Hz, 125 kHz bw, SF 5 to 12
INFO: Lora multi-SF channel 3> radio 0, IF 200000 Hz, 125 kHz bw, SF 5 to 12
INFO: Lora multi-SF channel 4> radio 1, IF -300000 Hz, 125 kHz bw, SF 5 to 12
INFO: Lora multi-SF channel 5> radio 1, IF -100000 Hz, 125 kHz bw, SF 5 to 12
INFO: Lora multi-SF channel 6> radio 1, IF 100000 Hz, 125 kHz bw, SF 5 to 12
INFO: Lora multi-SF channel 7> radio 1, IF 300000 Hz, 125 kHz bw, SF 5 to 12
INFO: Lora std channel> radio 0, IF 300000 Hz, 500000 Hz bw, SF 8, Explicit header
INFO: FSK channel 8 disabled
INFO: global_conf.json does contain a JSON object named gateway_conf, parsing gateway parameters
INFO: gateway MAC address is configured to BB555A0000000001
INFO: server hostname or IP address is configured to “eu1.cloud.thethings.network”
INFO: upstream port is configured to “1700”
INFO: downstream port is configured to “1700”
INFO: downstream keep-alive interval is configured to 10 seconds
INFO: statistics display interval is configured to 30 seconds
INFO: upstream PUSH_DATA time-out is configured to 100 ms
INFO: packets received with a valid CRC will be forwarded
INFO: packets received with a CRC error will NOT be forwarded
INFO: packets received with no CRC will NOT be forwarded
INFO: GPS serial port path is configured to “/dev/ttyS”
INFO: Reference latitude is configured to 0.000000 deg
INFO: Reference longitude is configured to 0.000000 deg
INFO: Reference altitude is configured to 0 meters
INFO: Beaconing period is configured to 0 seconds
INFO: Beaconing signal will be emitted at 869525000 Hz
INFO: Beaconing datarate is set to SF9
INFO: Beaconing modulation bandwidth is set to 125000Hz
INFO: Beaconing TX power is set to 14dBm
INFO: Beaconing information descriptor is set to 0
INFO: global_conf.json does contain a JSON object named debug_conf, parsing debug parameters
INFO: got 2 debug reference payload
INFO: reference payload ID 0 is 0xCAFE1234
INFO: reference payload ID 1 is 0xCAFE2345
INFO: setting debug log file name to loragw_hal.log
WARNING: [main] impossible to open /dev/ttyS for GPS sync (check permissions)
CoreCell reset through GPIO24…
SX1261 reset through GPIO24…
CoreCell power enable through GPIO2…
CoreCell ADC reset through GPIO22…
Opening SPI communication interface
Note: chip version is 0x00 (v0.0)
ERROR: Failed to set SX1250_0 in STANDBY_RC mode
ERROR: failed to setup radio 0
ERROR: [main] failed to start the concentrator
tyro@rpiz:~/LR1302_loraWAN/LR1302_HAL/sx1302_hal/packet_forwarder $
tyro@rpiz:~/LR1302_loraWAN/LR1302_HAL/sx1302_hal/packet_forwarder $ ls /dev/s*
/dev/serial0 /dev/spidev0.0 /dev/stderr /dev/stdout
/dev/serial1 /dev/spidev0.1 /dev/stdin
/dev/shm:
/dev/snd:
by-path controlC0 pcmC0D0p seq timer